Manufacturing Process

There are various Pipe Fittings Manufacturing Process that used to manufacture Elbow, Tee, Reducer and other pipe fittings.

Pipe Fittings are manufactured from bar, Seamless Pipe and from Welded Pipe with filler material (ERW & EFW pipes cannot be used to manufactured fittings). Large diameter fittings are manufactured from Plate.

Each product is manufactured with its own special process. The most appropriate manufacturing process for each product will be decided with consideration of its material, sizes, shape, use, standards and special properties.

For more information please contact our
Customer Support Center:

Customer Support Center

Butt-Welding

To manufacture wrought fittings various methods are used, these are the some types of Hot forming and cold forming processes:

• Hot forming or Extrusion Method

• Hydraulic Bulge method – Cold forming

• UO or Single weld seam Method

• Monaka or Double weld seam Method

• Deep Drawing Method for caps

• Flare Method for Stub ends

Mandrel Method(Hot Forming)

One of the most common manufacturing methods for manufacturing Elbows from pipes.

After heating the raw material, it is pushed over a die called "mandrel" which allows the pipe to expand and bend simultaneously. Applicable to a wide size range.

Characteristics of mandrel bending strongly depend on the integrated shape and dimensions of the mandrel.

Elbows manufactured by using hot mandrel bending have advantages of small thickness deviation and shorter bending radius than those of any other bending method type.

Extrusion method (Cold Forming)

In cold Extrusion method, a pipe with the same diameter as finished product is pushed through a die and formed into its desired shape.

It is usually applied to stainless steel small to medium sizes elbow

"UO" Method (Welding)

In this method the plate is cut out into a specially designed shape, it is formed first into a U-shape using a die and then into an O-shape or tubular form using another die, that is why this method is known as UO method. Once the fittings formed in tumbler shaped it is welded from inside and outside of the closing seam. A cut plate is 1st from in U shape and then in O shape

Hot Forming Die Bending method

In this method the pipe is been inspected before any process. Then after cutting out pipe into specified length, it goes under elliptical forming using a die shown in the picture. For producing a specified radius for elbow, it bends in another die. In the next step the elbow goes under heat treatment. In the end shot blasting, cleaning, beveling and coating are done respectively to finalize the product.

Hydraulic Bulge method (Cold Forming)

Cut piece of Pipe is placed in hydraulic die and liquid is fill inside the pipe, Hydraulic pressure pushes out the branch, in the fixed opening in the die.

This method gives the good surface finish. However, higher thickness Tee cannot be manufactured by this method.

"Monaka" method

This manufacturing method is similar to Elbows, using steel plates as the raw material

In this method two pieces of raw material plates cut out symmetrically and are press-formed and welded together.

Hot Extrusion Method

Tee with large diameters, heavy wall thickness and/or special material with challenging workability that cannot be manufactured using the hydraulic bulge method are manufactured using hot Extrusion Method.

In hot Extrusion Method, Normally Bigger diameter pipe is used than the finished product size, the branch outlet is extruded from the pipe with help of extrusion tool.

Other dimensions of body and branch can also be adjusted by pressing the die if required.

Outer Die method

One of the most common method for manufacturing Reducers is using an outer die.

The pipe is cut and pressed in the outer die; compressing the one end of the pipe into a smaller size. This method is useful for manufacturing of small to medium size of reducers.

Plate Forming Method

Plates can also be used to manufacture Reducers.

In an UO method, plate is cut in a specially designed shape which is formed into a U-shape and an O-shape respectively, then finished with a single weld seam.

Deep Drawing method

CAPs are manufactured by Deep Drawing method. In this method, Plate is cut out in a circle and formed by deep drawing die.

Flaring method

Stub Ends or Lap Joints Flange are manufactured by flaring method. Pipe end is a flare or spared out to form flange face. Stub ends are also manufactured by forging in which forge block are machined to final dimension.

FORGED FITTINGS

There are multiple options for Fittings deformation using the forging concept. The two most common processes are open and closed die forging. While similar in the basic idea of using pressure and temperature to modify material, the two types of forging are made distinct by their use of dies to form the metal.

Open Die Forging

Open die forging is the process of deforming a piece of metal between multiple dies that do not completely enclose the material. The metal is altered as the dies “hammer” or “stamp” the material through a series of movements until the desired shape is achieved. Products formed through open forging often need secondary machining and refining to achieve the tolerances required for the finished specifications. Open die forging is often used for short run forgings of parts that are simple, rather than complex, in design, such as discs, rings, sleeves, cylinders and shafts. Custom shapes can also be produced with open die forging. The repeated working of the material through the deformation process increases the strength of the grain structure. Some additional benefits of open die forging include improved fatigue resistance and strength.

Closed Die Forging

Closed die forging (also referred to as impression die forging) is a metal deformation process that uses pressure to compress a piece of metal to fill an enclosed die impression. In some closed die forging processes, a succession of impression dies are used to modify the shape of the material into the final desired shape and form. The type of material, tightness of tolerances, and need for heat treatment can determine the number of passes the product requires through the dies.